Info Page Glow Engines A to K Glow Engines L to O Glow Engines P to Z Spark Ignition Engines Diesel Engines Jet Engines Engine Spares Steam Engines |
| Aluminum silencer for 23cc - 26cc engines x2 at £36 each |
| Tuned Pipe Water Cooled 15cc cost £25 |
| CMB90 COUPLING Cost £25 1/4" ER11 collet |
| CMB90 COUPLING X 2 Cost £37 1/4" ER11 collet |
| 2 x octura-kool-clamp-1,5 inch cost 47 |
| KM HPI Baja 5B 5T SS-Alloy Flip Style Gas Cap |
| Mini FPV 2.4Ghz Video A/V TX& RX 4.0Km FPV wireless transmitter works in 2370-2510MHz ISM band of the FM audio and video transmitter module. Single-chip module design, the chip integrates VCO, PLL, broadband FM video demodulator, FM audio demodulation, small size, low power consumption, the module features high sensitivity; to patch or plug-in package, user installation requirements requirements.
Working frequency:
CH1/CH5: 2410/2370MHz
CH2/CH6: 2430/2390MHz
CH3/CH7: 2450/2490MHz
CH4/CH8: 2470/2510MHz
|
Receiver -RC302
★ Receive Frequency: 2370-2510MHz; 8 channels
★ Receiver sensitivity:-90dBm
★ Frequency Control: Built-in PLL(Phase Locked Loop)
★ Dual AV output: output analog audio and video signals directly
★ antenna interface: SMA (the pin)
★ supply voltage: 6.5-15V
★ Supply Current: 100mA
★ Dimension: 61 * 52 * 13mm; aluminum alloy | Transmitter -TS321 ★ transmission frequency: 2370-2510MHz; 8 channels
★ Transmit Power: 27dBm/500mW
★ Transmission Distance:> 4000 meters
★ Frequency Control: Built-in PLL(Phase Locked Loop)
★ AV input: direct input analog audio and video signals
★ antenna interface: SMA (the pin)
★ supply voltage: 6.5-12V
★ Supply Current: 300mA
★ Dimension: 55 * 26 * 17mm |
| EEC2000L01 .21 Class Electric power
conversion Transmission Ratio: 1.6
Fix Counter gear 32P 25T (Input gear required 32P 17T Out put gear 32P 27T) Cost £55 |
| Gearbox for 540 Size Motor Specification:
1: 540 or 550 Motor
2: L 35mm x W 39mm x H 47mm
3: Output 4mm
4: Color Black
5: 3:1 Ratio
6: Ball raced |
| 1:5 planetary gear box |
 | 3cells 11.1V 6000mAh 40C 80C FUSION Hard Case LiPo Battery Pack three of these! Specifications
Type: Lithium Polymer
Model No.: CC600040P
Capacity: 6000mAh
Voltage: 11.1V
Configuration: 3S1P
Size: 37 x 47 x 139mm
Weight: 450g
Continuous Discharge: 40C
Burst Discharge: 80C |
| SEAKING Brushless Motor ESC Program Card Product Number: LED_PC2B
For SEAKING series boat ESC;
Size: 88mm (L) 58mm (W) 14mm (H)
Weight: 40g.
Input Voltage: 4.8-6V Should work with TURNIGY MARINE 35A |
| Seaking 180A Brushless ESC 429U
"Forward" mode and "Forward/Backward" mode
Throttle signal loss protection
8 steps of timing adjustment
Switch mode built-in BEC
Specification
- Continuous Current: 180A
- Burst Current: 360A
- Input Voltage: 2–6 cells Li-Po
- BEC Output: 5.8V@3A
- Dimensions: 72x68x34mm
- Net Weight: 165g |
| SKYRC Proteus X520 3D 1280KV or 3Y 730KV For large scale rc boat (1.5-2m length).
There are six connectors on the motor and the user can switch the wire configuration to either Delta Configuration=More RPM or alternatively Star Configuration=More Torque X520 3D System
Watts: 5280W (7hp)
Max Voltage: 23V
Max Amps: 229A
Resistance: 0.0046
KV (RPM/volt): 1280
Max RPM: 30000
Length: 102mm
Diameter (w/fins): 55.8mm
Weight: 925g
Shaft Diameter: 8mm
Length of extend shaft: 30mm
Features
High Quality Bearings
Rotor - 4 Pole Neodymium Magnets
Stator- Super Thin Laminations
Super Strength 8mm shaft
6 Connectors |
| RCMB/MHZUSA Z Drive This is a surface drive for big powerboats. The Z drive is designed for gas engines such as the Zenoah G260PUM and Quickdraw 25 on boats over 45 inches. Examples of hulls where this drive can be applied include the MHZ DPX-24 Nimbus Batboat-large version.
Technical Details:
Length of the outside shaft 175 mm (6.9 inch)
Height 150 mm (5.9 inch)
Weight 695 gram (24.5 oz)
Prop Shaft d=1/4" standard drive dog
Max Prop Size 72 mm |
ATTENTION: The switching off process of MPS works with a hall effect sensor they are influenced by magnet fields, run all cables carrying high current (>100A) at least 3cm from the switch acutator. | Emcotec MPS Gas-Cap-Powerswitch •Electronic power switch in Gas-Cap design for receiver sets, ignitions etc.
•On/Off via external magnet
•An inserted magnet is off, removing it turns on
•Magnet held in the " Gas-Cap" by magnetic force
•On indicated by bright shining blue ring
•Absolute fail safe system with a combination of Reed-Contact and Hall-Sensor
•Input voltage 6.0V ... 12.6V
•Continuous current 5A, peak current 20A
•Flexible silicone 0.5 mm2 cross section cable, 30cm long
•High grade gold plated contacts (FCI)
•Mounting diameter: 15.5 mm, installation depth about 35mm
|
| MHZ-USA DPX-24 Nimbus - Stena Bulk Designed by
Ocke MANNERFELT 72" long |
| Brushless motor Cells: 3-4x Li-Poly
Rpm/v: 4000
Max. efficiency current: 8 - 10.5 A (>75%)
No load current / 10 V: 0,5 A
Current capacity: 40 A/60 s
Dimensions:31 x 30 mm
Shaft diameter: 3.17mm
Weight: 65 g |
| Brushless motor 2805-14 KV: 2840KV
Weight: 32g
Motor Dimensions: 28.7*26.7mm
Shaft Size: 3.17mm
Prop: 6x4/7x4
Battery: 2-3Li-Po
Idle current: 1.2A
Load current: 14.7A
Power (Watt): 160watt
ESC(A): 18A
Ohms: 0.073 |
| KB-45-10xl 580
Brushless motor 77mm x 45mm
77 mm long and 45 mm diameter
1200 kv
2 pole motor
max power 2400 watts
shaft size 6mm
weight is 557 grams
used in large vee hulls and cats 950 to 1100 mm on 5 to 8 cell lipos turning a 45mm to 48 mm prop |
| Black Mantis Brushless Inrunner motor BM2836-8 KV4950
30A ESC
2-4 cell Li-po battery
Dimension: ￠27.8X36（mm）
Shaft:￠3.175X12.0(mm)
Weight:66gTwo purchased |
| FSD 3600 KV Brushless Motor IM343
3600 RPM/V
Normal Current 45A
Max Current 52A
Voltage 8-18V
Max Efficiency 90%
No Load Current 1.9A
Internal Resistance 0.0119Ω
Motor Dimensions D=39.5mm L=58mm
Shaft Dimensions 3.14mm x 11mm |
| Motor mount for above |
| Aveox 600 Brushless 1419/2Y
probably 1.4in diameter motor with a 1.9in long rotor magnet.
Two turn early Y (star wound not delta)"sensor" coupling motor. The motor works perfectly with modern escs without connecting this plug - it could be removed except it kind of adds character! Another feature of this motor is the facility to adjust timing (the rear plate turns on slackening its mounting screws!).
Power output is on a par with a 0.46 ic engine, with props of around 12 X 6 drawing around 60 amps
sensor-type BL motors, where the Hall Effect Sensors are mechanically timed much like a brush-type motor endbell, for maximum efficiency in one direction |
| 3674 BRUSHLESS WATERCOOLED MOTOR Equivalent power to a 91 sport nitro engine (£53)
KV 2045
Max AMPS 90
Max volts 15v
1400Watts
Weight 350 grams
36mm motor diameter
74mm long
43mm waterjacket diameter
25mm hole centres
5mm shaft diameter |
| 540 Brushed 12V 45t COST-11 |
| AEO Model P1 High Voltage and Precision Wattmeter BK153
Specifications
Dimension: 38 x 49 x 17mm
Net Weight: 57g
Working Voltage Range: 8 - 30V
Working Current Range: 0 - 100A
Working Temperature Range: - 20 to 50 Degree
Special Features
- Ultra portable and light weight
- Calibration of current`s standard
- Data comparing mode
- Manual calibration function built-in
- Using special current sensor
- High precision of measurement and low resistance |
| SKYRC Swordfish 120A ESC for Marine
Specifications
Forward with Reverse
Input Power:2-6S LiPo (25.2V Max)
On Resistance: 0.0002 Ohms
Continuous Current:120Amp
Switching BEC:6V 3Amp
Thermal Overload Protection:Yes
Dimensions(L×W×H):72.2×43×15.8mm(2.85×1.69×0.621in)
Weight: 97.2g(3.42oz)
|
| Wooden 24x18 propeller Cost 17 |
| 450 Bronze x50mm For 82kb outboard cost £14 |
| 45mm prop Diameter 45mm
Shaft Diameter 4.76mm
Weight 13g
Cross Weight (kg) 0.03 |
| AquaCraft GrimRacer
L40x57 Propeller Size : 40mm
Pitch: 57mm (1.44:1)
Shaft Hole : Ø4.7mm
No. of Blades : 3
Material : Copper-Beryllium |
| VXP 8014 CNC ALLOY PROPELLER
80mm diameter X 1.4 pitch
1/4" 6.36mm bore
Cost £49 |
| 2-Blade 45mm Ø4.7mm Propeller Size : 45mm
Pitch: 63 (1.4:1)
Shaft Hole : Ø4.7mm
No. of Blade : 2 (Left-Hand)
Weight : 2.8g / 1oz
Material : Plastic(ABS + PP)
Colour: Black |
| Pro Boat Brushless Outboard PRB4020 For use with above motor Length: 177mm
Width: 68mm
Height: 209mm
Weight: 380g
Flex shaft diameter: 3.78mm
Coupling diameter 5mm
Max prop size 45mm |
 | 30.5" Fiberglass Epoxy F-1 For above outboard
Material: Epoxy Fiberglass
Length: (mm) 780
Width: (mm) 320
Height: (mm) 140
Net Weight: (kg) 1.006
Video |
| Brushless motor info |
| Italian Crucible Furnace 1Kg
220 – 240 volt
Max temp 2000°F (1100°C)
LED display
Precision temperature control
Melts Aluminum, Copper, Gold, Lead, Silver, Sterling Silver, Tin & Zinc.
Grooved graphite crucible |
| Solder Pot Model:ST-21C
Power:150w
Input voltage: 220v
Temperature:200-450℃
Melting Time:5-15min
Capacity:500g
Pot Diameter:50mm |
| Rapid one Brushless R/C Boat
Requires a single 4 cell 4000mAh 20C lipo
Length: 820mm
Width: 240mm
Height: 80mm
Weight : 1680g
Motor: 3660 size 1620kv Water-cooled brushless motor
ESC: 125A water-cooled
Drive system: 4mm
htx 10 kg digital metal geared servo |
| Sea Eagle
suitable for class 'C' class 'D' OMRA racing
1420mm OAL
320mm Beam |
| Waverider Apache 58 |
| Riva Florida |
| Riva Aquarama Dimensions 26” long
8” wide
7” high
Based on actual drawings
Leather covered seat cushions |
Cost £650
| 1955 RAF RSL (Range Safety Launch) 1640 
|
| |
| GWS FS-1 Failsafe plugs in-line between the throttle servo and the receiver. Sets the throttle servo to neutral on loss of radio signal, or? loss of battery power preventing runaway.
40mm x 21mm x 8.5mm
weight 7 grams |
GAZ-126 Head Lock Gyro manual | GAZ-126 Head Lock Gyro GAZ-126 uses AVCS (Angular Vector Control), which makes the head lock more steady, it is a gyro with the a dual rate head lock.
AVCS System: The rudder trim changes with wind and other meteorological changes.
Operating voltage:4V-6V
Operating temperature:-10C to +45C
Size:27mm(L) x28.5mm(W) x18mm(H) Weight:20g |
| SOLDERLESS RC SWITCH
Solderless Connections
Onboard Operational Regulator. Can be powered from 7.4v RX LiPo Systems.
Can handle loads up to 21A at 30v
SMT Design
Shakeproof Vibrationproof Crashproof Construction
Standard 3 Wire Futaba Connection
Receiver Current Draw 4mA engaged, 21uA in quiescent state
Small 20mm x 18mm footprint
Ultra Lightweight. Only 4.2g |
| 30A RC High Current Switch
Receiver switch, 30 Amps rated.
This electronic design uses high power M.FET and current limit is extremely higher than mechanical switches.
●High current FET switch
●Internal Resistance (0.002 Ohm)
●Onboard LED indicator
●30A Continuous, 100A Pulsed
●Input: 4.8-30V
●Silicon wire AWG 18
●Length:12x58mm
●Weight:20g |
 | STM8S003 Digital Voltmeter 3 Digit 3.2-30V |
| Electro Marine FSW5 Switch
This unit installs directly in RX to operate 5 functions on/off from spare ch. on RX Only 1 function can be active at a time
|
| Stepping Remote Switch RCD3003 Manual 1 Servo signal input, control up to 7 devices
5-16V AUX Power input, total max 3.5A output
7 outputs, 500mA max current per channel
7 LED indicate working state
9 Preset mode
False trigger protection
Calibration feature,compatible with all RC system
Metal shield, reduce EMI
Weight, only 5 grams |
| 2-WAY Radio Control
Switch - non-latching Stick up for switch 1
Stick down for switch 2
Switching voltage can be from 2 – 24 Volts
Can use two independent supply voltages
switch up to 10A per circuit
Size 32mm x 25mm x 11mm |
| Voltron Mini GPS Data Logger V2 Press the button and turn on power hold for 3sec to Switch Km to mile Specifications: Operating Voltage: 4.8-8.4V
Operating current: 70mah
Data update: 1second
Recording Time: 18hr
Weight: 12g
Size: W18.20 H8.70 L68.60 |
| 4 X High-Voltage Generator Cost: £10 High voltage bipolar discharge distance: 10mm-20mm Input power cable length: about 10mm ( red is positive ) Dimensions: Φ24 * 63mm For pulse jet engine ignition |
| Waterproof Servo pushrod belows |
| Quick release servo connector |
| TURNIGY SERVO TESTER |
| EMAX ES08MD Digital Servo Digital Metal Gear Micro Servo
1520us 333mhz
torque:
4.8v 1.6 kgf.cm
6.0v 2.0 kgf.cm
Speed
4.8v 0.12 sec/60deg
6.0v 0.10 sec/60deg
weight: 12g
size: 32x11.5x24 |
| Futaba S3306MG High torque
Dual ball bearings
Metal gears
Water/dust resistant speed: 0.16 sec/60 at 6.0v
torque: 24.0 Kg-cm (333 oz-in) 6.0v
motor: 3 core
type: analogue
size: 66 x 30 x57.1mm
weight: 130g (4.59 oz) |
| MG90 Micro Servo SS105
- Metal Geared
- Full Ball Bearing
- Wire Length 150mm
Dimensions 23x12.2x29mm
Speed (4.8V) 0.11sec / 60 degrees
Speed (6.0V) 0.10sec / 60 degrees
Stall Torque (4.8V) 2.2 kg/cm
Stall Torque (6.0V) 2.5 kg/cm
Dead Band Width 10us
Voltage 4.8-6.0 Volts |
| Corona DS919MG Digital Servo Metal Gear Size: 22.5 x 11.5 x 24.6mm
Weight: 12.5g
Operating Voltage: 4.8V / 6.0V
Operating Current : 200mA / 240mA
speed : 0.07sec. 60o 0.06sec.60o
torque : 1.5kg.cm / 1.7kg.cm
Dead band : 3uSec
Potentiometer: 2 slider/Direct Drive
Ball bearing : MR85
Gear : Metal |
| VIGOR MG
Thin Wing Servo Operating Voltage: 4.8-6.0V
Torque: 1.4kgf.cm(21.0oz.in) at 4.8v
Speed: 0.14sec/60deg at 4.8v
Weight: 8.0g(.28oz)
Size: 25x8.7x21.6mm(.98x.34x.85in) |
| Turnigy MG959 Alloy Digital Metal Gear Servo
Milled from a single block of 6061 alloy with dual ball bearings and metal gearing
Control: +pulse width 1520usec
Dead Band:
Operating speed: 0.2sec / 60 degree
Stall torque @ 4.8V: 166 oz/in. (12.0kg.cm)
Stall torque @ 6.0V: 200 oz/in. (15.0kg.cm)
Motor type: Coreless motor
Potentiometer drive: Indirect drive
Dimensions: 40.2 x 20.1 x 36.8mm
Weight: 2.64oz. (75g) |
| MG996R SERVO
upgraded version of the MG995 servo. redesigned PCB and IC control system which makes it far more accurate. Its internal gearing and motor are also upgraded to improve dead bandwidth and centering. Digital
Metal Gear
Double Ball Bearing
Dimension : 40mm x 19mm x 43mm
Weight : 55g
Speed : 0.17sec / 60 degrees (4.8V)
Speed : 0.13sec / 60 degrees (6.0V)
Torque : 13 kg-cm (180.5 oz-in) 4.8V
Torque : 15 kg-cm (208.3 oz-in) at 6V
Operation Voltage : 4.8 - 7.2Volts
Gear Type: All Metal Gears |
| Metal MG995 Gear
Analog Servo
Coreless Motor
Metal Gears
Double Ball Bearing
Dimensions: 40 x 20 x 36.5mm
Weight: 1.78oz (48g)
Operating Speed (4.8V no load) : 0.17sec / 60 degrees
Speed (6.0V) : 0.13sec / 60 degrees
Torque (4.8V): (13kg/cm) (180oz/in.)
Torque (6.0V): (15kg/cm) (208oz/in.)
Dead Band Width: 4usec
Operation Voltage: 3.5 - 8.4Volts
|
DS1210 Digital Servo with aluminum body, titanium gears and dual ball bearing output shaft. Water/dust sealed case allows this servo to operate in some of the most extreme environments. | MKS DS1210 Digital Servo - Dead Band: 0.0002 ms
- Pulse Width Control
- Working Frequency: 120Hz
- Voltage: 4.8 ~6.0 V DC Volts
- Speed (4.8V): 0.15 sec/60°
- Speed (6V): 0.12 sec/60°
- Stall Torque (4.8V): 8.05 kg.cm (111.79 oz/in)
- Stall Torque (6V): 10 kg.cm (138.87 oz/in)
- Output Shaft Spline: Futaba
- Motor Type: DC Motor
- Potentiometer Drive: Direct
- Driver Type: FET
- Bearing: Dual Ball Bearings
- Gear Type: Titanium Gears
- Wire Length: 15.0 cm (5.9 in)
- Dimensions: 40X20X40.3 mm (1.57x0.79x1.58 in)
- Weight: 56 g (1.97 oz)
|
| Traxxas 2075 Digital Waterproof Servo Modulation: Digital
Torque: 6.0V: 125.0 oz-in (9.00 kg-cm)
Speed: 6.0V: 0.17 sec/60°
Weight: 1.59 oz (45.0 g)
Length: 2.17 in (55.1 mm)
Width: 0.79 in (20.1 mm)
Height: 1.50 in (38.1 mm)
Motor Type:
Gear Type: Plastic
Support: Dual Ball Bearings |
| RCS M8166 Metal Gear Super Torque Large Servo SS812
Dimensions (Length x Width x Height) 60.0 x 28.8 x 60.0mm
Operating Speed (6.0V) 0.21sec / 60 angle
Stall Torque (6.0V) 33.00 Kg-cm
Gear Material 4 Metal and 1 Plastic
Net Weight 154g
Dead Band Width 4usec
Operation Voltage 3.5V to 8.4V
- Double Ball Bearing Support
- Connector Wire Length 300mm
- Futaba, JR, Sanwa and Hitec Compatible |
| 9805MG Large Servo SS805
- Metal Gear
- Dust Resistant
- Double Ball Bearing
- Wire Length 300mm
65.5x30.5x55.5mm
Speed (6V) 0.24sec/60 degree
Stall Torque (6V) 20kg/cm
Dead Band Width 4usec
Voltage 6Volts |
| MKS DS 530 - Digital Cyclic Micro Servo Modulation: Digital
Torque: 4.8V: 43.1 oz-in (3.10 kg-cm)
6.0V: 44.9 oz-in (3.23 kg-cm)
Speed: 4.8V: 0.10 sec/60°
6.0V: 0.09 sec/60°
Dead band: 0.002ms
Weight: 0.53 oz (15.0 g)
Length: 0.91 in (23.1 mm)
Width: 0.47 in (11.9 mm)
Height: 0.91 in (23.1 mm)
Motor Type: Coreless
Gear Type: titanium alloy/Plastic
Rotation/Support: Dual Ball Bearings
360° Modifiable: YES
Programmable: YES |
| Traxxas Waterproof SubMicro Servo 2065 Modulation: Analog
Torque: 6.0V: 32.0 oz-in (2.30 kg-cm)
Speed: 6.0V: 0.20 sec/60°
Weight: 0.46 oz (13.0 g)
Length: 0.89 in (22.6 mm)
Width: 0.50 in (12.6 mm)
Height: 0.89 in (22.5 mm)
Gear Type: Plastic
Support: Bushing |
| KST DS125MG High Speed all Metal digital coreless motor Servo Digital Wing Servo
Precision Metal Gears
CNC Metal Case
360 deg Direct Drive Potentiometer
2 Ball Bearings
Voltage:4.5V-6.0V
Size:30*10*35.5mm
Torque: 7.00Kg.cm @6.0V
Torque: 6Kg.cm @4.8V
Speed: 0.12sec/60@6.0v
Speed: 0.15sec/60@4.8v
Weight: 28g
COST £19 |
| KST DS215MG High Speed all Metal digital coreless motor Servo Voltage:DC4.5V-8.5V
Size: 22.90*12*27.30mm
Torque:
3.70Kg.cm@7.4V
3.10Kg.cm@6.0V
2.50Kg.cm@4.8V
Speed:
0.05sec/60°@7.4V
0.06sec/60°@6.0V
0.07sec/60°@4.8V
Weight: 20g
Frequency: 1520us/333Hz, 800us-2200us
Motor: 12mm Coreless
Ball Bearing: 2BB
COST £25 |
| KST Digital Servo DS115MG Voltage: 4.8V-6.0V
Torque: 2.40Kg.cm@4.8V
3.00kg.cm@6.0V
Speed: 0.07 sec/60@4.8V
0.06sec/60@6.0V
Dimensions: 23*12*27*5mm
Freq: 1520us/333Hz, 800us-2200us
Weight: 20g
Motor: 12mm coreless
Ball Bearing 2BB
Metal gears |
Button the Select <Note: the key switch function, circulation patterns:
1.S-1 manual mode (Manual)
2.S-2-bit mode (Neutral)
3. S-3 automatic mode (Automatic)
Keys pulse width <Note: button switch function, circulation patterns:l
1 .50H analog servo signal cycle 20us frequency 50HZ
2 .125H digital the steering gear a signal cycle 8us frequency 125HZ
3. 250H Digital Servo signal cycle 4us frequency 250HZ
| Digital LCD 4 Servo Tester Specifications:
Input voltage: DC/4.8-6V
Output signal width :800-2200us
Can be synchronized output control 4 servos and used to compare the performance steering gear control of the steering servo output signal can be accurate to 2us (1 milliseconds = 1000 microseconds), you can test
the steering gear is able to respond to subtle changes. With PPM signal test function In the display the Input PPM signal changes while the Input the PPM signal synchronization output to the servo. Energized automatically enter manual mode (Manual) 20us 50H analogue servo signal cycle, frequency 50HZ, rotary potentiometers to decrease or Increase the width of the output pulse. Warning:
digital or analogue signal button to select the corresponding servos and then plug in the steering servo, to avoid damage to the steering servo |
| 24" Fiberglass Epoxy F-1 Tunnel Hull Material Epoxy Fiberglass
Length (mm) 600
Width (mm) 245
Height (mm) 120
Net Weight (kg) 0.62 |
| F1 Rowing Brushless Motor Shaft |
| Brushless Outboard Fiberglass Gelcoated Cowling - Aluminum CNC Construction - Water Cooled - Grease Fitting - Aluminum Adjustable Mount - Steering Linkage with Ball Connections at the Motor - Carbon Fiber Stabilizer with Water Pickup
Specs:
6.5" Tall
5.5" Legth
2.25" Width
Weight: 240 Grams (9oz)
450 watt
3000Kv
11.1 volt
40.5 amps
Out-runner Brushless Motor
Requires:
Bronze 432 Propeller
60 to 90 Amp ESC
3s 2200mah Min 30c LiPo |
| Motor of above outboard 450 watt
3000Kv
11.1 volt
40.5 amps
Out-runner Brushless Motor
Requires:
Bronze 432 Propeller
60 to 90 Amp ESC
3s 2200mah Min 30c LiPo |
Well designed MCU, with efficient code makes for faster sync and accurate timing. Fast clock cycle MCU combined with efficient code means 100,000rpm cpu cycle* Efficient FET's reduce heat and deliver sustained switching at high amp/voltage. Well designed PCB (6 layer) and circuit diagram handles high-amp without burnout. Large motor comptability. Smooth starts, linear throttle curve. Active water cooled heatsink that actually works | TURNIGY MARINE 35A Programmable settings:
Reverse
Low Voltage (none/2.6v/2.8v/3v/3.2v/3.4v)
Brake: (none/soft/hard)
Timing (0.00/3.75/7.50/11.25/15.00/
18.75/22.50/26.25)
Specifications:
Constant Current: 35A
Burst Current: 190A
Resistance: .0015 ohm
Battery: 2-3S Lipoly
BEC: 6v/ 1.5A
Motor Type: Sensorless Brushless
Size: 31.5 x 27.5 x 16mm
Weight: 32g |
| Watt Meter SkyRC WM-010 Measures energy (Wh) charge (Ah) power (W) current (A) voltage (V) Measures peak Amps, peak Watts ,voltage minimum (sag) Measures Celsius & Fahrenheit (optional probe) Auxiliary battery required for measurement to 0V Accurate – 0.01 A current and 0.01V voltage
handles 50 A continuous and 100 A peak at 60V Precision Alu-Chrom current sensing resistor |
| JG Props from Dumas Boats
E-20T - 1.5" dia - 2" pitch - .705"
F-20 - 1.562" dia - 2" pitch - .815"
G-20 - 1.625" dia - 2" pitch - .850"
F-22 - 1.562" dia - 2.25" pitch - .815"
G-22 - 1.625" dia - 2.25" pitch - .850"
F-25 - 1.562" dia - 2.50" pitch - .805"
G-25 - 1.625" dia - 2.50" pitch - .875"
H-25 - 1.750" dia - 2.50" pitch - .960"
H-27 - 1.750" dia - 2.75" pitch - .930"
I-27X - 1.875" dia - 2.75" pitch - 1.065"
I-27 - 1.875" dia - 2.75" pitch - 1.160"
I-30 - 1.875" dia - 3.00" pitch - .975"
J-30 - 2.00" dia - 3.00" pitch - 1.085"
J-35 - 2" dia - 3.5" pitch - 1.195"
3I-21 - 1.875" dia - 2.43" pitch - 1.545"
3I-22 - 1.875" dia - 2.63" pitch - 1.545"
RG-25 - 1.625" dia - 2.5" pitch - .93"
RH-25 - 1.750" dia - 2.5" pitch - 1.28"
RI-25 - 1.875" dia - 2.5" pitch - 1.38"
RH-27 - 1.750" dia - 2.75" pitch - 1.21"
RI-27 - 1.875" dia - 2.75" pitch - 1.51"
1.1 x 1 - 1.125" dia - 1" pitch - .39
RF-26-1 - 1.562" dia - 2.2" pitch - .895"
RG-26-1 - 1.625" dia - 2.25" pitch - .925" |
| Jimmy Gale designed Dumas/JG boat propellers. Lost wax investment cast from nickel aluminium bronze. All props are bored for a 3/16" shaft except for the last 3 which are bored 1/8". |
| AquaCraft GrimRacer
L40x57-Beryllium-Prop |
| Bronze three blade propeller Diameter 67mm
Pitch 113mm
Pitch ratio 1.7x
16000 rpm =
4.53 bhp
50.55 mph
thrust 175 lb
16000 rpm with 1.18 z drive = 18880 rpm
5.33 bhp
59.65 mph
thrust 206 lb |
| Copper-Beryllium AS 7016/2 Diameter 70mm
Pitch112mm
1.6 x pitch
Made by Arrow Shark
16000 rpm =
4.89 bhp
50.1 mph
thrust 189 lb
16000 rpm with 1.18 z drive = 18880
4.89 bhp
59.12 mph
thrust 223 lb |
| Aluminium AS 7016/2 propeller
Diameter 70mm
Pitch112mm
1.6 x pitch
Made by Arrow Shark
16000 rpm =
4.89 bhp
50.1 mph
thrust 189 lb
16000 rpm with 1.18 z drive = 18880
4.89 bhp
59.12 mph
thrust 223 lb |
| Aluminium AS 6717/3 propeller
Diameter 67mm
Pitch 114mm
Pitch ratio 1.7x
Weight 12g
Made by Arrow Shark
16000 rpm =
4.55 bhp
51.0 mph
thrust 176 lb
16000 rpm with 1.18 z drive = 18880
5.38 bhp
60.18 mph
thrust 208 lb |
| 1667 Prop 67mm diameter
1.6:1 pitch ? |
| RCMK H767 Stainless Propeller
Diameter 67mm
Pitch 114mm
Pitch ratio 1.7x
Weight 12g
16000 rpm =
4.55 bhp
51.0 mph
thrust 176 lb
16000 rpm with 1.18 z drive = 18880
5.38 bhp
60.18 mph
thrust 208 lb |
| 3.00 Stainless 4 Blade
Diameter 3.00
Pitch 5
1.66 x pitch ratio
Made by Ron Hill to order
16000 rpm =
6.57 bhp
56.81 mph
thrust 254 lb |
| 3.25 Stainless 4 Blade
Diameter 3.25
Pitch 4.7
1.44 x pitch ratio
Made by Ron Hill to order
16000 rpm =
7.25 bhp
53.4 mph
thrust 280 lb |
| 6717 Bronze PROP Diameter 67mm
Pitch 114mm
Pitch ratio 1.7x
Weight 12g
16000 rpm =
4.55 bhp
51.0 mph
thrust 176 lb
16000 rpm with 1.18 z drive = 18880
5.38 bhp
60.18 mph
thrust 208 lb |
| BRONZE X670 70mm propeller 70mm diameter
112mm pitch |
| Stainless propeller for 23-35cc
Diameter: 70mm
Pitch: 98mm16000 rpm =
4.27 bhp
43.84 mph
thrust 165 lb |
| 478 Aluminium Propeller 78mm Diameter 78mm
Pitch 109 16000 rpm =
5.93 bhp
48.76 mph
thrust 229 lb |
| NQD-757 757-6024
Boat Turbo JET |
| Boat Shaft
Length: 185 mm (mount to drivedog)
Sleeve diameter: 8 mm
Shaft diameter: 4 mm
Coupleing diameter: 3.17mm
Weight: 85 grams
4 mm drivedog
M4 threaded
3/16" + drivedog
Shaft: steel wire
Shaft tube: stainless steel
bushes: teflon-top bronze-bottom
|
| Hyperclene 80 ALUMINIUM CLEANER - NON ETCH Industrial Aluminium non-caustic cleaner, enough to make between 10 and 20 litres of working cleaning solution.
A mildly alkaline soak cleaning preparation for cleaning aluminium, generally prior to anodising or paint treatment.
Use warm for between 2 and 5 minutes |
| Carburettor & Engine cleaner Ultrasonic Cleaning Solution Concentrate 5Litre
cost £30
A specialist formulation for Ultrasonic baths for cleaning engine carburettors etc. It safely removes general soiling, carbon, petrol residue and grease etc. The cleaning process will not damage or darken metal components.
Add to water at a rate of 1 part to 10 parts of water. Operating temperature between 50 - 80 oC. Rinse all surfaces with clean water. |
| EP24R Carburettor & Engine cleaner Ultrasonic Cleaning Solution Concentrate 5Litre
cost £30
A specialist formulation for Ultrasonic baths for cleaning engine carburettors etc. It safely removes general soiling, carbon, petrol residue and grease etc. The cleaning process will not damage or darken metal components.
Add to water at a rate of 1 part to 10 parts of water. Operating temperature between 50 - 80 oC. Rinse all surfaces with clean water. |
 | 1kg Citric Acid |
 | 1 Litre Glacial Acetic Acid 99%
(Ethanoic Acid) |
| 2L ultrasonic cleaner
cost £43.00 50w ultrasonic
60w heater |
| Floureon 6L ultrasonic cleaner
cost £110 - 6L capacity tank.
- 40 KHz transducers.
- Timer 0-20 minutes.
- Heating from 20—80 Celsius.
- Bypass Louver for prolonged operation.
- Durable and strong heat resistance stainless steel construction.
- Needs only plain tap water to clean (add a tiny amount of washing-up liquid for further effectiveness) |
| Cream Of Tartar Potassium Bitartrate Acid pH of 3.557 To remove discoloration and oxidation from aluminium one table spoon to a pint of water and boil for 10 to 20 mins. |
| Micro Balloons These ultra-light hollow glass micro bubbles can be blended with epoxy resins to create a superb lightweight filler. Once cured the filler is non-water permeable, and can be sanded easily. |
| 5 gram W0.5 micron oil based Diamond Polishing and Lapping Paste |
| LOCTITE 638 HIGH STRENGTH RETAINING COMPOUND 3ml High strength retainer, used widely in industry for metal bonding,engines, as a sealer, etc |
SP Colloidal Silica is an agent which is used to control the thixotropy or sag characteristics of a resin system. By adding colloidal silica powder in varying amounts to a resin mix containing the other filler types mentioned, the handling and flow characteristics can be controlled. Relatively small quantities added to a resin mix containing glass bubbles or microballoons will give non-sag properties and impart easier handling. Colloidal silica is also used with microfibres to produce a mix suitable for use as a high strength, non-sagging structural adhesive, particularly for non-absorbent materials such as grp. | SP106 Colloidal Silica Filler for Epoxy Resin Product Details:
Composition: Silicon dioxide
Appearance: White powder
Particle Size: 0.012 microns
Bulk Density: 50g/litre approx
|
| Araldite 2000 50cc system two 2011 (slow)
two 2012 (rapid) |
| ARALDITE 2000 MIXPAC TYPE DM 200 |
| |
| Step Down Power Regulator Module 12V Input voltage: 12-50V
Output Voltage: 6-24V ( set to 9V)
Output current: Rated current 3A ,
Conversion efficiency: Up to 80%
Input Capacitance : 50v330uf
Output Capacitance: 16v1000uf
Operating temperature: Industrial grade (-40 ℃ to +85 ℃)
Full load temperature rise: 40 ℃
Connection mode: Jack with screw fix
Dimension: 5.2cm*4.5cm*3cmV |
| 12 Amp contacts 6V volt Relay Size: 19 x 15.4 x 15.5mm
Contact rating: 15A 24V DC
Single pole change over
Contact material: AgSnO2
Operate/release time 10ms/5ms max.
Pull in voltage: 75% coil voltage max.
Drop out voltage 5% min. |
| Bridge Rectifier 3 Phase SQL35A-10 Amps: 35A
Voltage: 1000V
Dimensions: 61 x 32 x 12mm
Fixing hole 0.24 inch/ 6mm |
| Roller-Ball Tilt Switch/Sensor-0028 |
| Stainless steel push button switch Momentary push action
12 Volt
20 Amp
19mm hole diameter |
| Stainless steel push button switch Bulgin MP0037/3
21.5mm diameter
Front sealed to IP68
S.P. push to make
Rated 1 Amp 50 Volt
Hole diameter 19.2mm
Depth 28mm long |
| 8 AWG R/B Silicone Wire 6.8mm Overall Diameter
3.75mm conductor Diameter
burst 200amp
continuous 100amp |
| 14AWG Silicon Wire od 3.6mm
conductor area 2.1mm²
continious current 32A |
| 12 AWG Black red
Silicone Wire 12 awg Silicone Cable
4.5mm Diameter
88 amp at 600v |
| 14AWG LIPO Copper Flexible Silicone Wire Type: 14 AWG
Heatproof: 200°C
Nominal Voltage: 600V
Temperature Range:-60oC~+200oC
Conductor: Copper Clad Aluminum
Insulation: Silicone
Color: Orange Blue Yellow
Length: 1 meter each |
| Polymax 6.0mm bullet Connectors Rated for applications in excess of 160amps |
| 6.0mm Gold Bullet Connector |
| 4.0mm Gold Banana Bullet Connector Diameter: 4.0mm
Length: 2cm |
| JETI 5.5MM ANTI SPARK GOLD CONNECTORS A SMD resistor does away with the usual flash that occurS during connection whick can harm the male and female plug. Designed to go between your battery and ESC and reduce the initial current to the controller Maximum current 150 amps |
| 8.0mm Gold Bullet Connectors |
| 12V-24v DC micro Centrifugal water pump Voltage : DC 12-24 volts
(red dot is positive)
Flow rate: 3 to 4 liters/min
Pump Diameter: 3 cm
Pump Length: 6.3 cm
Out water hole diameter: 4 mm
Weight: 70 g |
| 12v fluid pump Multi chamber diaphram pump with no metal to fluid contact and no shaft seals to wear or leak. Specification:
- Working voltage: DC 3-12V
- Empty load current: 0.18A
- Load current: 0.3A
- Max.flow: 2-3L/mins
- Max.pressure: 1-2.5kgs
- Lift: 1-25m
- Max. suction: 2m
- tube diameter: out 9mm, in 6mm
- Install size: 100*45*62mm
- Weight: 110g |
| 24V dc gear pump
Length 135mm
Width 50mm
Height 55mm
inlet: 4mm bore 6.5mm od
capacity: 2.8 lt/pm
Maximum outlet pressure: 3 kg
MODEL: CS-0720A
|
| Mini 6-12V Water/Oil Pump 6-12V
Water, Diesel or Oil
Bronze Gears |
| Mini 130 Water Pump DC 12V Diaphragm Electric Motor Self-priming Cost £5 (two purchased) No-load current: 50mA
Suitable voltage: DC 6V-12V
Weight: 35g |
| Submersible Micro Brushless Water Pump DC 12V 3m 240L/H Cost £4.00 (two purchased) |
| ARM DSO201 Digital Storage Oscilloscope Display 2.8″ Color TFT LCD
Display Resolution 320×240
Display Color 65K
Analog bandwidth 0 - 1MHz
Max sample rate 1Msps 12Bits
Sample memory depth 4096 Point
Horizontal sensitivity 1uS/Divï½?10S/Div (1-2-5 Step)
Vertical sensitivity 10mV/Divï½?10V/Div (with ×1 probe)
Input impedance >500KΩ
Max input voltage 80Vpp (by ×1 probe)
Coupling DC
Trig modes Auto, Norma, Single, None and Scan
Functionalities: Automatic measurement: frequency, cycle, duty, Vpp, Vram, Vavg and DC voltage
Precise vertical measurement with markers
Precise horizontal measurement with markers
Rising/falling edge trigger
Trig level adjustable with indicator
Trig sensitivity adjustable with indicator
Hold/run feature
Test signal Built-in 10Hzï½?1MHz (1-2-5 Step)
Waveform storage SD card
PC connection via USB as SD card reader
Upgrade via USB
3.7V Chargeable Lithium battery / USB
Dimension 105mm X 53mm X 8mm
Pc connection: Mini USB B-Type |
| McCoy tether car by Nylint Cost £120 Reproduction midget race car |
| Lectra Starter 500 1979 marine engine starter belt is 40 tooth long as standard Cost £50 |
| 10:1 Right Angle Gear Box It has two male input shafts approx 5 mm diameter and single female output shaft 6mm diameter, at 90 degree to the input shafts. the casing is aluminium and is 47mm high x 40 mm long x 22mm thick. |
